One Gauge New

AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352


AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352

AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352    AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352

For X-Series Boost Controller Display Gauge 80PSI MAP Sensor. Part Number 30-4350 Superseded to 30-0352.

Not CARB Legal: Not for sale or street use in CA & CARB states. (NOTE: The original 30-4350 Tru Boost Controller Gauge is discontinued and has been replaced with the 30-0352 X-Series Tru-BoostX Controller Gauge, below). The Tru-BoostX Boost Controller Gauge delivers all of the features you loved about the original only now with AEMnet for data logging and a big, fat internal MAP sensor that can handle boost pressures up to 80 PSI of boost. The Tru-BoostX Boost Controller gauge delivers digital accuracy but with the simplicity of a manual boost controller. All programming is done using the faceplate buttons and no laptop is required.

AEMs specially designed Boost Control Solenoid and all necessary hardware is included. Program Two Boost Levels + Scramble Boost Setting Program two boost modes for different levels of performance (up to 80PSIg internal MAP sensor), and program a time-based scramble boost setting that is controlled using a switched input. You can also turn off the controller and use the gauge as a display. Change Wastegate Open PressureIdeal for reducing boost spikes and improving spool up. Display Boost Levels in PSIg (PSI), BAR or kPa (PAS) See your boost in the units you prefer, and scale the 24 outer LEDs to match your peak boost levels for the perfect sweeping motion.

Set Alarms and Display Peak BoostSet the 24 green outer LEDs to flash based on boost pressure so you are alerted to an overboost condition. A ground output is included for triggering an optional LED warning light. Select the B button to see peak boost level and clear the value using the menu.

Overboost Protection Built InProtects your engine from an overboost condition by shutting the boost control solenoid off until it is reactivated by you through the buttons on the faceplate. Integrated Error ProtectionAlerts you to a fault if the boost control solenoid is shorted or disconnected so you are never left guessing whether the Tru-BoostX is operational. Datalog using AEMnet CAN busOutputting channels over AEMnet provides so much more than just boost pressure! Send 13 channels of data over a 2-wire connection, including boost pressure, peak boost, boost target, boost scramble duty, overboost status, wastegate crack pressure, boost control solenoid status and more. A boost display gauge and boost controller in one!

Easy to program no laptop required. Boost control solenoid and all necessary hardware included. On-board 80PSIg MAP sensorno upgrade kit needed for high boost vehicles. Two boost level settings and scramble boost setting. Wastegate open pressure setting for controlling boost spikes and faster spool.

Display boost levels in PSI, BAR or kPa. Overboost protection and programmable alarms, ground output for optional LED warning light.

X-Series design for the best visibility (87% larger center LED and 33% larger face design). X-Series dimensions make it easier to install (0.825 overall depth, 0.20 cup depth). AEMnet CAN bus enabled for data logging (13 channels of data over 2-wire connection).

24 programmable green outer LEDs. Auto dimming sensor for ideal brightness day or night. Your address must be confirmed. Buyers who pay with unconfirmed addresses will not be accepted.

We always look to satisfy our customers in whatever needs they may have. Any product you return must be in the same condition you received it and in the original packaging. The item "AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352" is in sale since Wednesday, November 4, 2020. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Gauges\Boost Gauges". The seller is "abotrading" and is located in Santee, California.

This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.

  1. Superseded Part Number: A boost display gauge and boost controller in one
  2. Modified Item: No
  3. Custom Bundle: No
  4. California Prop 65 Warning: Cancer & Reproductive Harm
  5. Include 3: Boost Control Solenoid
  6. Include 5: A ground output
  7. Include 4: All necessary hardware
  8. New Feature 2: Internal MAP sensor
  9. Manufacturer Part Number: 30-0352
  10. Diameter: Standard 52mm (2-1/16) cup
  11. Display boost levels: PSI, BAR or kPa
  12. Gauge Type: Tru-BoostX Gauge-Type Boost Controller
  13. New Feature 1: AEMnet for data logging
  14. Other Part Number: 30-4350
  15. Brand: AEM
  16. Fitment Type: Performance/Custom
  17. Non-Domestic Product: No
  18. Warranty: 1 Year


AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352    AEM For X-Series Boost Controller Display Gauge 80PSI MAP Sensor 30-0352